Write your Feed Back
Teensy 3.2 Development Board is a direct, 100% compatible replacement for Teensy 3.1. It is fully compatible with all shields and add-on boards made for Teensy 3.1 The main change is an improved 3.3V regulator, to allow Teensy to directly power ESP8266 Wifi, WIZ820io (W5200) Ethernet, and other power-hungry 3.3V devices.
The Teensy 3.2’s power output is specified at 250 mA and the maximum voltage input at 6 volts, due to PCB thermal dissipation limits. However, the actual regulator chip is capable of up to 10 volts input, and up to 500 mA output. These higher limits are intended to allow Teensy 3.2 to be more rugged when used with non-USB power sources which aren’t well regulated 5-volt sources.
The Teensy breadboard-friendly development board with loads of features in a, well, teensy package. The Teensy 3.2 brings a 32 bit ARM Cortex microprocessor into the mix so you can do some serious number crunching.The Teensy 3.2 comes pre-flashed with a bootloader so you can program it using the onboard USB micro-B connector. No external programmer needed! You can program for the Teensy in your favorite program editor using C or you can install the Teensyduino add-on for the Arduino IDE and write Arduino sketches for Teensy!
Teensy 3.2 has the same size, shape & pinout; is compatible with code written for Teensy 3.0/3.1, and is well supported on the Arduino IDE using Teensyduino.The processor on the Teensy also has access to the USB and can emulate any kind of USB device you need it to be, making it great for USB-MIDI and other HID projects. The 32-bit processor brings a few other features to the table as well, such as multiple channels of Direct Memory Access, several high-resolution ADCs, and even an I2S digital audio interface! There are also 4 separate interval timers plus a delay timer! Oh yeah, and all pins have interrupt capability. Also, it can provide a system voltage of 3.3V to other devices at up to 100mA.All of this functionality is jammed into a 1.4 x 0.7-inch board with all headers on a 0.1″ grid so you can slap in on a breadboard and get to work!
We are an official UK distributor for the Teensy range so you can be assured of the quality.
Specifications:
| Processor | MK20DX256VLH7 |
| Core | Cortex-M4 |
| Rated Speed | 72 MHz |
| Overclockable | 96 MHz |
| Flash Memory | 256 kbytes |
| Bandwidth | 192 Mbytes/sec |
| Cache | 256 Bytes |
| RAM | 64 kbytes |
| EEPROM | 2 kbytes |
| Direct Memory Access | 16 Channels |
| Digital I/O | 34 Pins |
| Voltage Output | 3.3V |
| Voltage Input | 5V Tolerant |
| Analog Input | 21 Pins |
| Converters | 2 |
| Resolution | 16 Bits |
| Prog Gain Amp | 2 |
| Touch Sensing | 12 Pins |
| Comparators | 3 |
| Analog Output | 1 pin |
| DAC Resolution | 12 Bits |
| Timers | Total 12 |
| FTM Type 3 | |
| PWM Outputs 12 Pins | |
| PDB Type 1 | |
| CMT (infrared) Type 1 | |
| LPTMR Type 1 | |
| PIT (interval) Type 4 | |
| Systick 1 | |
| RTC (date/time) ** 1 | |
| With FIFOs | 2 |
| High Res Baud | 3 |
| Fast Clock | 2 |
| Communication | USB 1 |
| Serial 3 | |
| With FIFOs 2 | |
| High Res Baud 3 | |
| Fast Clock 2 | |
| SPI 1 | |
| With FIFOs 1 | |
| I2C 2 | |
| CAN Bus 1 | |
| I2S Audio 1 | |
| FIFO Size 8 | |
| Shipment Weight | 0.09 kg |
